Mokuロックイン アンプは、デュアル位相復調を使用して信号の X 成分と Y 成分を決定します。復調信号の位相は、復調信号のプロパティを調整することで Python でシフトできます。

この例では、復調信号の位相を調整する方法を示します。

#
# Moku example: Phase change in Moku Lock-In Amplifier
#
# This example demonstrates how you can shift the phase of the demodulation signal
# in the Lock-In Amplifier instrument
#
# (c) 2024 Liquid Pty. Ltd.
#
# This is configured for Moku:Lab and is compatible with Moku:Go and Moku:Pro
#
# Setup : loopback Moku output 2 to input 1 with a BNC cable.
#
# The phase of the demodulation signal is then swept
# a full 360 degrees and the resulting LIA output DC signal 
# reflects the phase offset between the PLL and input 1.
#
from moku.instruments import LockInAmp
import statistics
import matplotlib.pyplot as plt

# Launch Lock In Amplifier and connect to your device via IP
i = LockInAmp('192.168.2.74', force_connect=True)
try:
   # Configure analog input port 1 as 50 Ohm and 0 dB attenuation
   i.set_frontend(1, coupling='DC', impedance='50Ohm', attenuation='0dB')   
   # Output a 1MHz sine wave and demodulate at same
   i.set_demodulation(mode='Internal', frequency=1e6)
   i.set_filter(corner_frequency=1e1, slope="Slope6dB")
   # Output the 'X' (I) signal and the local-oscillator sine wave on the two
   # DAC channels. 
   i.set_aux_output(frequency=1e6, amplitude=1)
   i.set_outputs(main='X', aux='Aux', main_offset=0, aux_offset=0)
   
   i.use_pid("Off")
   i.set_gain(main=0, aux=0)
   # Monitor the I and Q signals from the mixer, before filtering
   i.set_monitor(1, 'Input1')
   i.set_monitor(2, 'MainOutput')
   # Trigger on Monitor 'B' ('I' signal), rising edge, 0V with 0.1V hysteresis
   i.set_trigger(source='ProbeB', edge='Rising', hysteresis=0.1)
   # View +- 0.1 second, ie trigger in the centre
   i.set_timebase(-2e-6, 2e-6)
   
   # Set up the plotting parameters
   plt.figure(num="Moku Lock-in Amplifier")
   plt.ylabel("Voltage (V)")
   plt.xlabel("Time [s]")

   line1, = plt.plot([], label='Input 1')
   line2, = plt.plot([], label='LIA X out')

   # Configure labels for axes
   ax = plt.gca()
   plt.pause(1)
   # This loops through a phase range of 0 to 350 degrees with a step size of 10
   for a in range(0, 351, 10):
       # Set a demodulation phase
       i.set_demodulation(mode='Internal', phase=a)
       data = i.get_data(wait_complete=True, wait_reacquire=True)
       dc2 = data['ch2']
       # Print out the demodulation phase and mean value of the output
       print(f'New Phase: {a}')
       print(f'Mean: {statistics.mean(dc2)}')
       # Update the Plotting
       line1.set_ydata(data['ch1'])
       line1.set_xdata(data['time'])
       
       line2.set_ydata(data['ch2'])
       line2.set_xdata(data['time'])
       
       plt.pause(0.1)
       plt.legend(loc='upper left')
       # Ensure frequency axis is a tight fit
       ax.relim()
       ax.autoscale_view()
finally:
   # Close the connection to the Moku device
   # This ensures network resources and released correctly
   i.relinquish_ownership()