Contact Us
If you still have questions or prefer to get help directly from an agent, please submit a request.
We’ll get back to you as soon as possible.
Moku:Lab Instruments
-
Moku:Go
Moku:Go Arbitrary Waveform Generator Moku:Go Data Logger Moku:Go Frequency Response Analyzer Moku:Go Logic Analyzer & Pattern Generator Moku:Go Oscilloscope & Voltmeter Moku:Go PID Controller Moku:Go Spectrum Analyzer Moku:Go Waveform Generator Moku:Go Power Supplies Moku:Go Digital Filter Box Moku:Go FIR Filter Builder Moku:Go Lock-in Amplifier
- Moku:Lab
- Moku:Pro
Moku:Lab Arbitrary Waveform Generator
- Custom Arbitrary Waveform Generator example
- What file formats does the Moku:Lab Arbitrary Waveform Generator support ?
- Can the Arbitrary Waveform Generator be triggered?
- How can I upload custom waveforms from the iPad?
- What file formats are supported in the Moku:Lab Data Logger?
- Example AWG custom waveform
Moku:Lab Data Logger
- What is the main difference between the Moku Oscilloscope and the Data Logger instruments?
- For how long can the Data Logger record ?
- How can I read data from .li files?
- How can I import a .CSV file from Moku:Lab’s Data Logger into MATLAB?
- How to delete a file in the Data Logger?
- Logging speed of Moku Data Logger
Moku:Lab Frequency Response Analyzer
- Frequency Response of EFI / RFI filter
- Frequency Response Analyzer and harmonics
- Can Moku:Lab analyze control loops ?
- Using the Frequency Response analyzer to measure inductance
- How can I plot the ratio of input 1 and input 2?
- How is the magnitude in dBm calculated in Moku:Lab’s Frequency Response Analyzer?
Moku:Lab Laser Lock Box
- What is the input to output latency for Laser Lock Box
- How does Moku:Lab's Laser Lock Box apply gain to the input?
- Can you do fringe-side locking with Moku:Lab's Laser Lock Box?
- If Moku:Lab only has two output channels, how is it possible to generate feedback control signals as well as the modulation tone and scanning waveform?
- Can I adjust the corner frequency of the low-pass filter?
- What laser locking techniques does the Laser Lock Box support?
- Does it lock continuous wave and pulsed lasers?
- What if my actuator can't take negative voltages?
- Moku:Lab's Laser Lock Box : When and how should I use the slow PID controller?
- Can I set a lower corner frequency for the lowpass filter in the laser lock box?
- Can I add an offset to the oscillator or scan output in laser lock box?
- How do I generate a custom filter for laser lock box with scipy?
Moku:Lab Lock-in Amplifier
- Moku:Lab Lock-in Amplifier, external trigger
- Stimulated Raman Scattering Microscopy
- How do I adjust the sensitivity of the Lock-In Amplifier?
- Can you do frequency domain analysis in the lock-in amplifier?
- What's the difference between external and external (PLL) mode?
- How does Moku:Lab's Lock-in Amplifier measure small signals with 12-bit ADCs?
- Can Moku:Lab's Lock-in Amplifier output a signal to drive a modulator?
- Can I adjust the corner frequency of the low-pass filter?
- What is the maximum rate at which I can save data, and how many points can I save?
- Can the Lock-in Amplifier demodulate using an external source?
- Does the Lock-in Amplifier include a PID controller for feedback applications?
- The Lock-in Amplifier can readout I and Q (X and Y). What about R and theta?
- Can Moku:Lab perform phase unwrapping demodulation
- How do I demodulate a signal at a higher harmonic with an external (PLL) reference?
Moku:Lab Oscilloscope
- How do I adjust the sampling rate of the oscilloscope?
- Moku:Lab oscilloscope probe compensation
- Can I set the channel offset in screen divisions while zooming?
- What is the difference between "Normal" and "Precision" acquisition modes?
- What are the definitions of the Oscilloscope's measurements?
- What measurements can the Oscilloscope make?
- What is timebase setting "roll"?
- 100:1 High Voltage probe
- How to match channel scale settings in the Oscilloscope
- What is the main difference between the Moku Oscilloscope and the Data Logger instruments?
Moku:Lab Phasemeter
- What's the difference between Moku:Lab phasemeter and a frequency counter?
- Phasemeter output waveform resolution
- How does Moku:Lab calculate Allan Deviation?
- Can I measure the phase or frequency difference between the two input channels?
- How does Moku:Lab calculate the Power Spectral Density?
- What reference does the Phasemeter measure against?
- How to remove drift in Phasemeter measurement
- How to change the units in the Phasemeter?
- How do I calculate the power density spectrum if the measured phase has a constant drift?
Moku:Lab PID Controller
- How do you adjust the input gain or invert the PID input?
- How do you adjust the setpoint in PID controller?
- What is the closed-loop bandwidth of the PID?
- How can I invert my controller's response?
- How does the PID control matrix work?
- Can I set the PID controller by Ki, Kp, and Kd?
- What do the different colored buttons mean when configuring a PID controller?
Moku:Lab Spectrum Analyzer
- Moku:Lab's spectrum analyzer 3-D timeseries
- How to improve the resolution bandwidth in spectrum analyzer?
- What's the difference between the spectrum analyzer and oscilloscope FFT?
- How do I generate waveforms on Moku:Lab’s analog outputs while running the Spectrum Analyzer?
- How do I track a peak?
- Spectrum Analyzer units of measure
Moku:Lab Waveform Generator
- How does the 'load' affect the waveform generator?
- Waveform generator and Amplitude Modulation
- Waveform Generator and Frequency Modulation
- Can you generate a chirp with Moku:Lab's waveform generator?
- What are my options for triggered burst mode?
- What is the triggered sweep mode?
- Python Waveform Generator : burst mode
Popular Articles
- How to connect Moku:Lab via USB in Windows
- Python: Oscilloscope (plotting)
- How do I update Moku:Lab’s firmware?
- Python: Arbitrary Waveform Generator
- Python: Lock-in Amplifier
- How can I import a .CSV file from Moku:Lab’s Data Logger into MATLAB?
- How do I find the serial number of a Moku ?
- What do all the ports do on the Moku:Lab?
- Can I indicate where I am touching the iPad’s screen while presenting using Moku:Lab?